Seat Alhambra Key Problems
Seat's MPV jumbo family is among the best in its class when it comes down to resales value. With a new model available for sale, the jumbo family MPV is even more impressive.
There are a variety of reasons why the key fob could not function properly, such as a dead coin battery, water damage, receiver module problems or signal interference. This article will guide you through the steps needed to get it back in working order.
Water Damage
If your key fob for the seat alhambra withstands the wash cycle, a dip in the water or a pool, it is equipped with a waterproof chip. But be careful not to do this often because prolonged exposure to water increases the chance of the key fob getting damaged. If your key fob stops functioning after being exposed to rain or clean tap water, unplug the battery and clean the electronic component using a paper towel. Dry it completely before replacing the battery. If the key fob has been exposed to soapy or salty water it is recommended you clean the chip using isopropyl or an electronic cleaner.
Faulty Receiver Module
If the key fob does not lock or unlock after having replaced the button cell battery It is possible that the receiver module has a fault. The good thing is that this is a relatively simple and inexpensive repair, you can just disconnect the 12 volt battery for about a couple of minutes (first take off the negative cable and press the horn button numerous times) to remove any remaining electricity and then reconnect it in reverse order e.g. Positive cable first, then negative.
ESP Warning Light – If the ESP symbol flashes, this is normal. It means that you are driving over terrain that has poor traction. This could be due to snow, gravel or surface water. If the ESP warning light is constantly shining, it is a sign that there is a glitch in the system. It is best to be detected with a iCarsoft i908 Seat OBD Code Reader kit that will provide you with a specific fault description.
Dead Coin Battery
One of the most common reasons for the seat alhambra key not working is a dead coin battery. The key fob comes with a small button cell battery which keeps it powered. Replace it with a new battery that has the same dimensions, voltage and specs as the original. When replacing the battery on the key fob, remove the metal clips and make sure that the contacts of the key fob are clean and free of corrosion.
If the key fob has been exposed water, such as soapy or rain it is recommended to remove the battery and clean the electronic chip with isopropyl alcohol or a electronic cleaner prior to installing the new battery. The chip is sensitive to moisture and can be permanently damaged. If the key fob still doesn't function after replacing the battery it could be necessary to replace the key fob.
Faulty Receiver Module
If your key fob has stopped working after you replaced the battery but it did not help, or if it stopped working completely in a sudden manner it is possible that your receiver module might have developed an issue. The receiver module is responsible for capturing the radio frequency signals sent by the remote key fob and transform them into electrical commands that are then acted on by other modules in your car.
If the receiver module is faulty, it will not accept any commands from your remote key fob. In car seat key 'll be required to visit a service to reprogramme your key fob as well as a new receiver module.
The key fob is covered with rubber to prevent water from leaking into the electronic chip. If you dip the key fob into salted or soapy water it could damage the chip. If your key fob does not work, you can try cleaning the chip using isopropyl or an electronic cleaner.
If the keys are in a pair but the receiver module has developed a fault, you can try to reboot all electronics on board by removing the 12 volt battery for a short period of time. Then, reconnect the battery in reverse order (negative cable first before positive). This will reset the on-board electronic and restore their functionality.
Electronic Chip Faulty
The key fob is equipped with tiny electronic chips that transmits a signal to the receiver module each time the key is used. If the signal doesn't match the one that the car has stored the immobilizer is disabled and stop the car from starting. If, however, the key fob isn't working, and you are not able to reprogram it the issue could be due to a defective chip.
The chip in the key fob is not an irreplaceable part of the device and could need to be replaced to make it work again. This can be done by taking the key fob away from its case, and using pins or needles to touch each metal clip. You will need to replace these in the event that they have been damaged or damaged or corroded. Make sure the replacement batteries are of the same size, voltage, and specification as the original.
The Seat Alhambra is a well-designed and popular model however, like all cars it is not without its challenges. issues with specific parts or equipment. Some owners have reported issues with the climate control system that is automatic. It could fail and cause problems, and then get stuck in a certain setting. In the same way, the infotainment system has also been recognized to malfunction and even freeze screens.